
Low Profile, Winch-Ready Bumper That Maintains An OEM+ Aesthetic
The Backwoods Adventure Mods (BAM) Scout bumper for the 3rd Gen Tundra is engineered to deliver off-road utility with a sleek, low-profile design. Crafted for off-road enthusiasts, this bumper offers enhanced protection while maintaining the Tundra’s bold, aggressive look.
The standout feature of this bumper is its hybrid steel and aluminum design. The steel winch tray and core utilize factory mounting locations, while the lightweight aluminum shell keeps additional weight to a minimum. This bumper is perfect for the weekend warrior who wants added protection while maintaining an OEM+ aesthetic.
Find It Online
- BAM Scout Bumper: Check Price
Key Features

- Hybrid steel (winch plate and frame mount) and aluminum (shell) construction – big weight savings
- 41 lb. cradle
- 15 lb. shell
- 56 lb. total
- Corrosion resistant shell
- Integrated hidden winch
- Front recovery points
- Grade-8 hardware
- Minimal cutting required
- Relatively simple installation
- Free powder coat (included)
- Free shipping
- Lifetime warranty
- Fits 22+ Tundra
- Designed to follow body lines
- Works with factory sensors
- Can accommodate up to a 12K winch
Overall, a killer package and price point!
Installation

Tools Required
- 10 & 12mm sockets
- Ratchet
- 1/8″ & 1/4″ drill bits
- Power drill
- Slip joint pliers
- Adjustable wrench
- Flathead screwdriver or pry tool
- Dremel or other cutting tool
- Zip ties
- Razor or sandpaper
Note: The following steps are only for non-hybrid models equipped with the Active Air Dam. If you don’t have the active air dam, skip to Step 8. For hybrid models, refer to this link for air dam relocation instructions and a detailed video guide for the entire install.
Before installing the BAM Stealth bumper, you’ll need to remove the 3rd Gen Tundra’s front bumper cover. TRD Jon has a great write-up on how to do that – see his post here.
Installation took roughly 2 hours (taking photos included), and Backwoods was extremely responsive to my questions.
Step 1. Remove Active Air Dam

Remove the wire harness and (6) 10mm bolts to release the active air dam from the aluminum crash bar. (4) bolts are on the body, and (2) bolts are on the outer portions of the crash bar. As seen above, you will remove the two hinges on the outer portion of the crash bar.
Step 2. Relocate Air Dam

DO NOT cut off the tabs (circled above). You will only be cutting the section between the dotted lines. These tabs are needed to let the active air dam function properly once relocated.
Backwoods Adventure Mods recommends disassembling the motor to make this cut. I decided to test my luck and do it assembled. It works, but you will get a cleaner cut if you take it apart. Use your discretion.

Use an oscillating tool to make your cuts. The second cut will require more finesse. Following the radius of the cylinder, cut through the ribs of the arm, ensuring you don’t cut the cylinder.
When finished, set the assembly to the side.
Step 3. Relocate Hoses

Remove the hose from the clamp in the upper right (green tape). Then, remove the remaining marked 10mm and 12mm bolts.

Next, remove the hose from the clamp near the driver-side headlight. Pull the center metal post away from the support while pulling the hose down and behind the post. Then, you can reinstall the bolt to the post.
Step 4. Install Lower Relocation Mount

Caution: Use a short drill bit to ensure you don’t puncture the radiator.
Using the 12mm bolt you removed earlier, install the lower relocation bracket using the same bolt hole. Position the bracket about 1/8″ above the cross brace, as shown above, and mark the center of the hole on the bracket. Drill a 1/8″ pilot hole, then a 1/4″ hole.
Step 5. Bend Intercooler Coolant Bracket

Remove the hose mount from the post before bending, or it will break. Super glue will melt the part, which is expensive to replace; ask me how I know.
You must bend the bracket holding the coolant splitter for the line toward the radiator. Unfortunately, I could not take a picture while doing this step.
Referring to the photo above, hold the solid red line with slip joint pliers to prevent it from bending, and use an adjustable wrench to bend the dotted blue line towards the radiator. Bend the bracket enough so the hose clears the center support. About 1/2″ is enough. You may have to do this a couple of times to verify clearance
Step 6. Install Upper Relocation Mount

Install the upper relocation bracket using the supplied 1/4″ hardware and the third hole from the left on the radiator bracket. Loosely tighten the bolt so you can adjust the final positioning later.
Step 7. Attach Air Dam Motor

Using the supplied hardware, loosely attach the motor to the installed mounts. Once each bolt is threaded and finger-tight, you may fully tighten the bolts and reconnect the wiring to the motor.
Step 8. Install Winch Tray

There are (4) plastic frame plugs that need to be removed before adding the winch tray, two in front of the frame horns and two about 8″ behind them. Pop them out with a screwdriver or pry tool. Don’t worry about damaging them; they will not be reused. Take care not to stab your radiator while removing the plugs.
Next, lift the winch tray into place, ensuring the “wings” capture the frame. Use a long log bolt to hold it in place. There’s no need to put a nut on now, as the bolts will keep the tray in place as you install the rest of the bumper.
Step 9. Attach Recovery Points

The recovery points mount to the outside of the frame. The driver’s side is shown above. This step takes a little coordination. As you can see, the tray rests on the recovery points on the frame horn. To join the two parts, lift the winch tray and install the recovery mounts on the frame. Loosely install the included hardware to hold everything in place.
Repeat this step on the passenger side.
Step 10. Install Lower Bumper Supports

The weld nut plates are labeled Passenger and Driver. Thread the bolts through the plates before installing them to make threading them into the frame much easier.
Next, slide the weld nut plates into the frame, with the angled portion facing up and towards the front of the truck. Be sure to place the correct sides. Keep the bolts loose enough for final positioning later.

As seen above, I have already installed and tightened the lower bolts to the frame along with every other bolt. To save yourself some trouble, add the lower bracket before doing all of this.
Step 11. Tighten All Bolts

You can now tighten the remaining bolts. I suggest tightening factory frame horn bolts first and working your way around.
Optional: Add Winch
This is the best time to install a winch. The winch tray comes standard with winch mount holes pre-drilled into the tray. The holes allow fitment of most 15,000lb or less winches with a relocatable control box. BAM also included access holes on the bottom side of the tray for easy access to tighten the winch mount bolts.
Take measurements to ensure that your winch will fit before installation. Since each winch manufacturer has a specific installation process, please follow the OEM installation instructions. I had an Amazon winch I was installing, and the fairlead wouldn’t line up. Working on a solution there…
Step 12. Install Aluminum Bumper Cover

Slide the aluminum bumper over the winch tray and recovery points. Loosely install the bolts that hold the cover to the steel components to prevent it from falling.
Important: Install the (2) fairlead bolts first. Tighten the bolts finger tight, then back off by 1/2 turn so you can slide the cover for fitment/alignment.
Once you have the bumper cover centered, tighten the fairlead bolts, and then the rest of the bolts
Pro Tip: As you can see above, the passenger side sits slightly higher than the driver’s side due to the gap between the recovery point and the opening. Center top to bottom as best you can; it will save you an hour of fighting the bolts with the cover reinstalled later.
Step 13. Prep Cover For Cutting

The bumper will replace the lower portion of the factory plastic cover (outlined in red above). Before cutting, some items need to be addressed on the backside of the cover.
Step 14. Cut Wire Clips

With the front bumper cover removed, lay it on a blanket paint side down. Begin by cutting all the wire clips for the lower wire harness, taking care not to cut or pinch any wires.
Step 15. Reroute Wire Harness

Reroute the wire harness above the lower valance opening and secure it with zip ties. This will keep the wires out of the cutting path and prevent them from getting pinched upon installation. Do your best to keep the wires above the opening but below the two points that stick out where the bumper attaches to the core support bracket. Then, trim the zip ties.
Step 16. Remove Lower Valance

Use a nylon or plastic pry tool to separate the lower valance from the bumper cover. Pop all the tabs circled in red above.
Step 17. Cut Bumper Cover

Note: The final cuts will differ for each truck and require some fine-tuning. Cut the redline first, as this will leave room for fine-tuning later.
As seen above, you will be cutting just below the parking sensor. I started by cutting about 1/8″ above where the texture part starts and ended up trimming another 1/8″ off for the final cut.

Make your cut evenly across the bumper, ensuring you leave the tab mounts on the painted portion intact. Start with cutting according to the green line above. This will follow the valley between the valance and the end caps. If needed, you can trim more (up to the red line) later.
Once all the cuts are made, clean up any burs or melted edges with a razor or sandpaper.
Step 18. Reinstall Bumper & Grille Assembly

Snap the bumper into place and install the 10mm bolts and plastic retainers, leaving the bottom bracket mount bolts loose. Adjust the Stealth bumper to your liking and tighten the remaining bolts. As seen above, I cut too much to start. The lower mount brackets can be used to adjust the top-to-bottom alignment.
A friend pulled the bottom of the passenger-side bumper outward while I tightened the bolt to keep it in place. The driver’s side was pretty spot on; no adjustment was needed.
Double-check all the bolts, and you’re done!
Final Thoughts

The BAM Stealth Bumper for the 3rd Gen Tundra is designed to enhance off-road capability while maintaining an OEM+ appearance. Constructed from high-quality materials, it’s built to withstand impacts on the trail and protect the front end of your truck.

The improved approach angles, integrated winch mount, solid recovery points, and additional mounting locations for auxiliary lighting make it the perfect addition to your off-road rig. The fit and finish of the parts are next level, and I can’t overstate how much I love that this bumper adds a rugged appearance without going over the top. It remains true to its name, Stealth.
