
Control Arms That Balance Durability & Affordability
To complete my upgrades to my 2nd Gen Tundra, which included the OME Nitrocharger Plus Lift Kit and 35-inch Arroyo Tamarock M/T, I needed a solid set of upper control arms (UCAs). These would allow me to upgrade a crucial suspension component and get the most out of my new setup.
Upper control arms are a vital suspension component that connects to the vehicle frame at the upper shock mount tower and the steering knuckle. The upper of the two “wishbones” connects your upper and lower ball joints to the knuckle in an independent suspension system, allowing for articulation of the front wheels. This is a major factor in achieving a proper alignment and sets the geometry of your vehicle so that it stays straight when traveling down the road. It also ensures your tires stay flat and wear evenly. Not to mention the added benefits of more caster and articulation over a stock set.
Big shoutout to Mudify.com for these. They carry a ton of suspension components in stock and ship fast. Thanks, guys!
Find It Online
- Freedom Off-Road UCAs: Check Price
Overview

Proper articulation is particularly important when driving off-road, on uneven surfaces, or over large obstacles. The good folks at Mudify recommended pairing the Freedom Off-Road UCAs with my new lift. These come with built-in brake line attachments, eliminating the need for a separate bracket and helping with quicker installation. They are constructed from high-grade, 1.50-inch wide tubular steel and feature gusseting on both ends, adding rigidity.
Most importantly, they provide ball joint angle correction for lifted vehicles, allowing for proper alignment when paired with a 2-4 inch lift kit. While it’s possible to get alignment close to correct with stock UCAs, these ones are designed to restore the stock ride geometry while accounting for the additional clearances achieved by a suspension lift and larger, heavier tires.
Installation

Like most other brands, the UCAs are sold in pairs. They come fully assembled with heavy-duty OEM-style greaseable ball joints and hardened rubber bushings designed to reduce deflection and require minimal maintenance. The ball joints come pre-greased and are fully replaceable.
The only other items in the box were the nuts for the bottom of the ball joints that connect the UCAs to the steering knuckle and the cotter pins to secure them.
Tools Needed:
- Socket & Wrench Set
- Jack + Jack Stands
- Bungee Cord/Strap
- Hammer/Rubber Mallet
- Grease
- PB Blaster
A good set of wrenches, sockets, and a driver and socket wrench are all you need for this install, besides a lift. A hydraulic lift is ideal, but you can get the job done with a jack and jack stands.
You’ll want a bungee cord, strap, or other device to hold the knuckle out of the way while you work on your UCAs and a hammer to knock the knuckle free from the ball joint. The other important thing we recommend is grease. Red grease is fine, but we recommend CV axle grease. The UCA bolt will likely be dry when removed, and coating it with grease before reinstallation will minimize the chances of it becoming seized over time. This is particularly likely if you live somewhere coastal or with road salt.
Preparation

Start by getting your truck up on the lift and removing the tire on the side you’re starting on. It’s a great idea to hit the bolts you’ll be taking off with some PB Blaster or other penetrant spray so that you don’t have too much trouble getting your bolts out. Pull the tabs that secure your spray guards out on either side of the shock assembly; you’ll need to put your hands on either side there to remove the UCA bolt.
Step 1. Remove ABS & Brake Line Brackets

The UCA and knuckle both have lines attached; you’ll want to remove the brackets holding these so that they don’t stretch when you pull the wheel assembly out of the way. The UCA has attached wires for your ABS sensors, and the knuckle has your brake lines; you don’t want either to stretch.
Step 2. Loosen Nuts

First, remove the pin holding your upper ball joint bolt in place. Then, loosen the (2) nuts you need to take out of the UCA using your socket and open-ended wrenches, or if you can fit it with a proper jointed extension or an impact driver. That would be the one holding the upper ball joint into the knuckle, and the one holding the UCA in place at the back of the shock tower – this is a long bolt/nut combo, so you’ll need to get a wrench on either end.

If your knuckle doesn’t fall freely off the ball joint, which it likely won’t, you want to hit the flat part of the knuckle just under the ball joint that faces the front of the vehicle hard but carefully with your hammer. This should pop the knuckle free from the ball joint. It may take a couple of hits to accomplish this, so don’t be afraid to use some force.
It’s important to do this before removing the nut so that it catches the knuckle and doesn’t fall freely, putting unnecessary tension on the brake and electrical lines.
Step 3. Free CV Axle

This step is not necessary, but makes things a little easier. We did not want to pull the shock/spring assembly. To move the wheel assembly easily out of the way to the UCA, it’s best to free the CV axle from the hub. Remove the hub cover, pull the pin holding the nut in place, and remove it with a large wrench or, ideally, your impact driver.

If you need to give it a tap with a rubber mallet to get it to budge free, you can. At this point, you’ll want to attach your strap or bungee to the knuckle and another part of the vehicle, such as the coil spring or the frame. Just get it somewhere that’ll hold the wheel assembly up when you get the other nuts off.
Step 4. Remove UCA

Now that everything is secured, you can remove the nut holding the ball joint to the knuckle and then finish pulling the UCA bolt out. It’s a tight squeeze, but with some wiggling and repositioning, you should be able to slide the bolt out towards the front of the vehicle and remove it entirely.
Step 5. Install New UCA

Once you’ve greased your UCA bolt to avoid seizing, position it at the entrance of its bracket and maneuver your new one into place. Again, this may take some wiggling and repositioning to get at first, but it will go through eventually.
Then, you simply guide the bolt all the way through until it gets through the other arm of the UCA and the other end of the bracket.
Attach the nut to the UCA upper bolt and tighten it down at the static position, meaning hold it up where you believe it will generally be sitting when the truck is on the ground. Tightening it down at this position will keep unnecessary stress off the UCA bushings and prevent squeaking, which will happen if you tighten the nut while the UCA is hanging down and touching the shock or coil.
Step 6. Attach Ball Joint To Knuckle

Now, because your lower control arm, coil over, and the weight of your wheel assembly are pushing your hub downward, you’ll need to lower your truck enough to get a jack under the lower control arm and raise it. This will allow you to bring the knuckle up to meet the UCA, slip the ball joint bolt into the knuckle, and secure it with the nut.

Tighten the nut with an impact or plenty of force and a wrench, then secure it with the provided cotter pin.
Step 7. Final Reassembly

Now you can replace and re-tighten your CV axle through the hub and replace the hub cover. Then, reattach the brake and ABS line brackets to the new UCAs and spindle. Give everything a physical check to ensure you properly replaced and tightened all your nuts and bolts.
Finally, you can put your wheel back on and repeat the steps on the other side of the truck. Because these new UCAs will be a little off from the original geometry of your OEM ones, you’ll want to get an alignment right away to keep your truck running straight and your tires wearing properly.
Final Thoughts

These UCAs appear to be made with quality materials, and they’re pretty affordable for only (currently) ~$400 for the set. Quality control also seems good, as I didn’t notice any flaws or defects, and the installation went smoothly.
Honestly, I didn’t notice much difference in ride quality before and after the install, which is good. I did notice that everything in the steering was very sturdy. The alignment report was solid, with everything coming out in the green. The alignment tech did say that after a few checks, he noticed it pulled a little to the right, but the tests showed proper alignment. I didn’t notice any pull, so maybe my truck has always been that way. Not that I’m faulting any of my components here.
I look forward to getting this truck off-road soon and giving these UCAs and the rest of my new suspension a proper 4×4 test. Stay tuned!
