How To Replace 2nd Gen Tundra (3UR-FE) Spark Plugs – Detailed Step-By-Step Guide

Iridium Spark Plug From Denso

Replacing Your V8’s Spark Plugs – Restore Performance & Reliability

Spark plugs ignite the air/fuel mixture, creating an explosion that produces power via an electric arc between two electrodes. The leads are not touching, but they allow high-voltage electricity to jump the gap between them. This process aids combustion by connecting to the ignition coil, which generates the voltage required for the plug that allows the engine to run, all of which is managed by the Electronic Fuel Injection (EFI) system.

The replacement process isn’t overly complicated, but you’ll definitely want the right tools and a thorough understanding. This detailed, step-by-step guide will walk you through replacing your own spark plugs and keeping your Tundra running smoothly.

Find It Online

    Table of Contents

    The Case For Iridium Spark Plugs

    Denso Iridium Spark Plug Worn

    Spark plugs are made from extremely durable materials and can withstand millions of “explosions” before replacement. However, the explosions cause corrosion and a weaker spark, reducing efficiency and potentially resulting in misfiring or failure to fire. As spark plugs approach the end of their service life, the gap between the two electrodes widens, reducing efficiency and increasing the risk of misfiring. If a spark plug corrodes enough and breaks, serious damage to the engine cylinder can result.

    Iridium spark plugs reduce this risk longer than copper spark plugs; however, there is a loss of performance, as copper electrodes are a superior conductor during the shorter period of use. Iridium spark plugs are also more heat-resistant than platinum and use a small center electrode, which requires less voltage to generate a consistent spark. Toyota is a great company with smart folks, and the entire EFI is calibrated to the iridium spark plugs.

    The Right Spark Plug & Replacement Interval

    Denso Logo

    DENSO spark plugs slightly outperform NGK in dyno testing and live logs, but both offer an excellent OEM- or equivalent-quality. DENSO is the provider of spark plugs for Toyota’s 3UR-FE engine. I have NGK plugs in (pre-interview purchase) now, and I’ll wait until the next interval to swap to the OEM DENSO.

    Your spark plugs will begin to lose performance after 50,000 miles, and this is well short of the OEM recommendation. However, if you want the best possible performance and mileage, this is the ideal interval. The direct ignition coils have a longer interval and lifespan, but they begin to degrade at 100,000 miles, affecting power and mileage in a similar way to spark plugs.

    Iridium Spark Plugs & Online Retailers

    Spot Fake Spark Plugs

    Recommend purchase spark plugs from a Toyota OEM dealer (online or local), DENSO, NGK, or authorized distributor/retailer on the NGK or DENSO website. Unfortunately, spark plug counterfeiting is widespread, and it’s best to avoid Amazon or eBay, as you may not receive OEM-quality parts.

    DENSO and NGK both have guides on how to detect counterfeit plugs…

    How To Tell When Your Spark Plugs Need To Be Replaced

    How To Tell When Your Spark Plugs Need To Be Replaced - Diagram With Different Conditions

    Here are the more common signs that indicate whether your spark plugs need to be replaced…

    • Check engine light with misfire code
    • Rough idle
    • Sluggish throttle response or lack of power
    • Difficulty starting the engine, especially in cold weather
    • Gas mileage decline

    Installation

    Parts List:

    Materials List:

      Tools List:

      Step 1. Vehicle Preparation

      Disconnect Negative Battery Terminal

      • Turn off the vehicle if it is running and allow it to fully cool before starting work.
      • Ensure the vehicle is in park.
      • Ensure the parking brake is fully functional and engaged (depressed).
        • Disconnect the negative battery cable from the terminal using a 1/4-inch compact-head ratchet and a semi-deep 10mm socket.
        • Use penetrating oil on coil pack 10mm bolts 2 hours prior to aid in removal (optional)

        Step 2. Engine Bay Prep

        Remove Tundra Engine Cover

        • Place a protective cover over the hood to protect paint and other surfaces while working (recommended).
        • Remove the V-bank cover sub-assembly, AKA plastic engine cover.
          • Raise the front of the V-bank cover sub-assembly to detach the 2 pins.
          • Remove the 2 V-Bank cover hooks from the No.1 V-Bank cover bracket, and remove the V-Bank cover sub-assembly.
        • Clean the area around the ignition coil assembly and both valve covers with an all-purpose cleaner using a rag and brush.
        • Remove any excess cleaning product with a clean, dry rag.
        • Use 303 Aerospace Protectant and a clean rag to prevent debris from contaminating the engine when removing the coil packs, and to condition rubber and plastic components in and around both valve covers.

        Step 3. Remove Interferences On Driver (Left Hand) Side In Vicinity Of Valve Cover Ignition Coil Assemblies (Optional)

        2nd Gen Tundra Spark Plug Change

        If you have a small army of extensions, you can avoid removing the array of items blocking access. You’ll typically need to insert and remove the extension without the ratchet, then combine the ratchet with the extension once the extension is seated on the spark plug. An extra step, but much simpler and easier than attacking the myriad of hoses and other items to save time. Plus, justification for new tools if you don’t already have them.

        Step 4. Disconnect All Four Ignition Coil Assemblies

        Changing V8 Tundra Spark Plugs

        • Disconnect all eight coil pack connectors by squeezing the tab.
        • Gently move the coil pack connectors out of the way.
        • Secure coil pack connectors (optional).

        Step 5. Clean All Four Ignition Coil Assembly Connectors

        Clean Electrical Connectors

        • Use an electronic cleaner to remove debris from the coil pack connectors.
        • Allow to dry completely before applying dielectric grease or connecting in later steps.

        Step 6. Remove Ignition Coil Assembly Bolt

        Unbolting Tundra Coil Pack

        • Use a 1/4- or 3/8-inch compact ratchet and a 10mm shallow socket with an extension to remove the bolts.
        • Retain all hardware for reinstallation.

          Step 7. Remove Ignition Coil Assemblies

          Removing V8 Coil Pack On Toyota Tundra

          • Use your hand to pull the ignition coil straight back and out. Twist gently in both directions if required to loosen.
          • Record and/or number each coil pack to ensure it is returned to the same location it was removed from, or store in sequence to reinstall in the same position.
          • NOTE: The rubber gasket under the coil pack may remain in place (as shown in the photo above) or fall off; therefore, be attentive during removal and reinstallation to avoid loss.

          WARNING: Do not use pliers to remove coil packs, as doing so may cause damage requiring replacement.

          Step 8. Clean Engine Valve Cover Area

          Clean Engine Cover By Spark Plug Tube

          • Use a clean, lint-free rag to cover the spark plug tube during cleaning to prevent damage from contaminants.
          • Clean the valve cover gasket area under the ignition coil gasket with 303 Aerospace protectant and a clean rag to ensure a proper fit.

          CAUTION: DO NOT allow cleaner or any contamination in the engine interior. Recommend using a clean rag to cover the spark plug tube during cleaning to avoid damage.

          Step 9. Clean & Condition Ignition Coil Assembly

          Cleaning & Conditioning Tundra Ignition Coil Assembly

          • Ignition Coil Part Number (P/N) 90919-A2005 is $92.00 as of the time of the article. Proper care is essential for continued operation and reduced operating costs.
          • Use an electronic cleaner to remove debris from the ignition coil exterior and the connector internal and external surfaces, and allow them to dry.
          • Use 303 Aerospace Protectant on a clean, soft, new cotton, non-lint-forming rag to condition rubber and plastic, but DO NOT spray or allow it inside the coil pack, as it is not electronics-safe.
          • Use silicone spray to condition the coil pack exterior, which will protect the plastic from becoming brittle, increase the life span, and help prevent leaks (optional)
          • If silicone spray is applied, ensure the ignition coil is fully dry before reinstallation.

          Step 10. Apply Dielectric Grease To Ignition Coil Assembly

          Dielectric Grease On Coil Pack

          • Use an applicator (such as a Q-Tip) to apply a small amount of dielectric grease inside the spark plug boot to create a thin coat on the walls, preventing water intrusion and shorting.
          • Dielectric grease is an electrical insulator; caution must be taken on where to apply and not to use an excessive amount, which can attract contaminants and prevent proper function.
          • Do not apply any dielectric grease to the conductive coil inside the coil pack, or the function will be impaired. Roughly .25″ or less from the tip is all that is required.

          Step 11. Apply Dielectric Grease To Outside Of Connector

          Grease Coil Pack Electrical Connector Housing

          • Use an applicator (Q-Tip) and place a small amount of dielectric grease to form a thin coat on the outside of the ignition coil electrical connection to prevent water intrusion and shorting.
          • Dielectric grease is an electrical insulator; do not use an excessive amount, which can attract contaminants and impair or prevent proper function.

          CAUTION: Do not apply any dielectric grease to the internal connection, or the pins, or the ignition coil may not perform properly.

          Step 12. Remove Spark Plug From Location Ignition Coil Assembly

          Removing Spark Plug On 2nd Gen Tundra

          • I recommend a compact or offset flex-Head ratchet, 16mm spark plug socket, and extensions. The Ko-Ken spark plug socket pictured above has tabs to secure the spark plug and prevent loss inside the engine, which is a great feature. The offset or flex head feature will help you navigate around obstacles.
          • Once the spark plug is loose, I recommend removing the ratchet from the extension and completing the removal by hand, using the knurling to reduce time and interference.

          WARNING: DO NOT use an impact wrench or driver to remove spark plugs.

          Step 13. Inspect Spark Plug

          Used Tundra Spark Plug

            Check for any abnormalities; there are some terrific online resources to determine the health and interval based on your plug’s appearance.

            Step 14. Prepare New Spark Plugs (Part 1)

            New NGK Spark Plug For Tundra

            DENSO 3421

            • Use a gap or spark plug gap tool to verify .044.”
            • DENSO: Do not change the gap on iridium spark plugs to prevent electrode damage. If the spark plug is out of specification, replace it with a new plug.
            • NOTE: If the packaging is damaged, do not install the spark plug; obtain a replacement.

            NGK 4904

            • Use a gap or spark plug gap tool to verify .043″ and adjust if required
            • Adjust the gap by moving only the ground electrode.
            • CAUTION: Applying pressure or prying force to the fine wire center electrode or insulator will damage the spark plug.
            • To widen, use a Lang or equivalent spark plug tool that pulls only the ground electrode, without touching the center electrode or porcelain.
            • To close, gently tap the plug, electrode first, on a hard surface.
            • NOTE: Do not adjust the gap more than .008″ in either direction, as the ground and center electrode will not align properly, hindering performance and reducing service life.
            • NOTE: If the packaging is damaged, do not install the spark plug; obtain a replacement.

            Step 15. Prepare New Spark Plugs (Part 2)

            Dielectric Grease Application On Spark Plug

            • Apply a thin coat of dielectric grease using an applicator (Q-Tip) to the ceramic portion to enable coil pack removal, prevent water intrusion, and prevent shorts.
              • CAUTION: Do not apply dielectric grease to any other area of the spark plug or in excessive amounts, as it will impair or prevent proper function.
            • CAUTION: Do not apply anti-seize to the NGK 4904 or DENSO 3421 spark plugs threads.
              • NGK: Trivalent plating finish on threads provides corrosion resistance and acts as a release agent for removal. Anti-seize is a lubricant that alters torque by up to 20 percent and reduces the risk of thread damage and/or metal shell stretch. Thread breakage can also occur, requiring the removal of the cylinder head for repair. In addition, metal shell stretch from over-torque changes the heat rating and can result in engine damage due to pre-ignition.
              • DENSO: Anti-seize is not recommended due to additional tightening caused by an incorrect torque setting, which can damage the spark plug or cause loss due to engine vibration.

            Step 16. Assemble Spark Plug Extension

            Spark Plug Extension Wrench

            • Spark plug female threads are (recessed) deep inside the valve cover in the spark plug; it’s critical not to cross-thread the spark plug.
            • Combine the 3/8 extension and 16mm spark plug socket.
            • Place the spark plug from Step 10 into the 16 mm spark plug socket.

            Step 17. Install Spark Plug

            Installing New Spark Plugs On 2nd Gen Tundra

            • Insert the spark plug and extension by hand into the valve cover.
            • You should feel the spark plug move into position and seat by rotating counter-clockwise (CCW) initially to ensure the threads are mated, then rotate clockwise (CW).
            • Use the extension knurling to tighten the spark plug by hand.
            • When you can no longer tighten, stop and use a ratchet to continue tightening, but do not tighten to the full torque spec.

            WARNING: DO NOT use an impact wrench or driver to install spark plugs.

            Step 18. Torque Spark Plugs

            3UR-FE Spark Plug Replacement

            Use a 3/8 compact flex-head torque wrench and tighten the spark plug to 180 in-lbs. (15 ft-lbs.).

            Step 19. Assemble Ignition Coil & Reinstall

            Coil Pack Assembly

            • The rubber gasket can, and often will, either remain on the engine or fall off.
            • Be sure to reinstall the rubber gasket on the ignition coil pack, as shown in the photo above, before reinserting it into the spark plug tube.

            Step 20. Install Ignition Coil Assembly Bolt & Re-Connect

            Replacing Ignition Coil

            • Install the bolt by hand to ensure it is seated properly in the threads. The gasket will provide some counterforce.
            • Use a 3/8 compact flex-head ratchet, a 10mm shallow socket, and a 3/8 extension to install the bolts.
            • Use a torque wrench to tighten the ignition coil assembly bolt to 80 in-lb.

            Step 21. Repeat Steps 4-20 For Next Three Spark Plugs

            Follow Steps 4-20.

            Step 22. Reinstall/Replace Interferences Removed (If Applicable) On Driver (LH) Side

            Tundra Spark Plug Maintenance

            Step 23. Remove Passenger (Right Hand) Side Interferences

            Passenger's Side Spark Plug Swap

            There are some components on the passenger side that must be removed, which will add time, but overall, access is easier once they are removed.

            CAUTION: The two hose clamps shown in the photo above, on the left near the firewall, are SHARP and can cause injury.

            Step 24. Disconnect Vacuum Hose From Air Cleaner Hose Assembly

            Remove Vacuum Line

            A hose clamp tool should not be required, but if you do use one, be careful, as the connection on the vacuum hose is very small and can break easily.

            Step 25. Disconnect Ventilation Hose From Air Cleaner Hose Assembly

            Remove Ventilation Hose

            • Use a pair of flat-tip serrated pliers to compress the wire hose clamp.

            CAUTION: Be sure to reinstall the wire hose clamp in the same position, or leaks may result.

            Step 26. Loosen Two Hose Clamps On Air Cleaner Hose Assembly

            Loosen Air Intake Bolts

            • Use a ratchet and 10mm shallow socket to remove.
            • The torque spec for re-tightening the bolts on both hose clamps is 35 in-lbs.

            Step 27. Remove Air Cleaner Hose Assembly

            Remove Air Cleaner Assembly

            • Slide the hose assembly off the throttle body and away from the air box connection, and store it in another location.
            • I recommend that while the air cleaner hose assembly is removed, you inspect for cleanliness and overall condition.

            Step 28. Disconnect Mass Air Flow (MAF) Sensor From Air Cleaner Assembly

            Disconnect MAF Sensor

            • If unable to remove by hand, use a pair of electrical disconnect pliers.

            CAUTION: Be sure to compress the tab at the top, or the lower portion may break with the pliers.

            Step 29. Disconnect No. 2 Ventilation Hose On Passenger (Right Hand) Side In Vicinity Of Valve Cover

            Replacing Tundra Gen 2.5 Spark Plugs

            • Use a pair of flat-tip serrated pliers to compress the wire hose clamp.
            • Hose grip pliers may be required if unable to remove by hand.

            CAUTION: Be sure to reinstall the wire hose clamp in the same position, or leaks may result.

            Step 30. Unhook Air Cleaner Assembly Wire Harness Clamp & Cap

            Disconnect Wire Harness

            • Use a flat tip screw driver to compress the tab as shown above and allow the cable to be released.
            • Once loose, move the harness gently out of the way, but avoid stressing the cables.

            CAUTION: Use care when moving to avoid damage to the EFI system.

            Step 31. Remove Air Cleaner Element Cover

            Tundra Air Box

            Pull up on each tab as shown in the photo above to release the air cleaner element cover, then set it aside for later reinstallation.

            Step 32. Remove Air Cleaner Element

            Remove Air Cleaner

            Remove and inspect for reinstallation or replacement as required.

            Step 33. Remove Both Air Cleaner Case Bolts

            Removing Tundra Intake Box

            • Use a 1/4 or 3/8 ratchet and extension to loosen both bolts.
            • NOTE: The bolts are capture in the air cleaner case a single unit.
            • NOTE: Torque spec is 44 in-lb for both air cleaner case bolts.

            WARNING: Over-torquing air cleaner case bolts will damage the rubber dampers.

            Step 34. Remove Engine Wiring Harness Interferences On Passenger (Right Hand) Side

            Removing Engine Harness

            • Remove the engine wiring harness bracket connectors using a flat tip screw driver or panel clip tool.
            • Once loose, move the harness gently off the threaded stud and out of the way, but avoid stressing the cables, as they are semi-rigid.

            CAUTION: Use care when moving the wiring harness to avoid damage to the EFI system.

            Step 35. Repeat Steps 4-20 For The Next Three Spark Plugs On Passenger (RH) Side

            Follow previous steps.

            Step 36. Reinstall/Replace Any Obstructions Or Interferences Removed On Passenger (RH) Side

            How To Replace 2nd Gen Tundra Spark Plugs

            Step 37. Reconnect Battery Negative Terminal

            Reconnect the negative battery cable to the terminal using a 1/4-inch compact-head ratchet and a semi-deep 10mm socket.

            Final Thoughts

            That’s it! Enjoy the confidence knowing that the materials, care, and precision you’ve used aren’t matched by anyone else! Early preventative maintenance is an inexpensive way to help support the longevity of your vehicle.

            You’ll notice I used NGK after describing that the OEM DENSO is superior. Unfortunately, that knowledge, thanks to TK-421 Tuning, was obtained after installation. So, I’ll be replacing them with DENSO on the next maintenance cycle. Plus, you don’t have to adjust the gap, which I did on every NGK, and that added time to the task. Regardless, both are OEM quality and will provide excellent service.

            Subscribe
            Notify of
            guest

            0 Comments
            Newest
            Oldest Most Voted
            0
            Questions or Comments?x
            ()
            x